Post: Setting up xlink kai on ps3
Options
09-10-2010, 03:07 PM
#1
Bluffed
Wasnp
Ok , so you want to play Playstation 3 on XLink Kai ? No problem , just read and apply the following steps carefully.
1. Start up XLink Kai first before you switch on your Playstation 3 .
2. Switch on your Playstation 3 & you should see a message that says : DNS Error . Don't panic, it is supposed to do that . Here is a movie showing what will happen :
PS3 DNS Error - YouTube
3. Now start up a Playstation 3 game with a lan option . Go to the multiplayer part of the game and go to the lan option . Press Join Game .
Here is a movie showing the Rainbow Six Vegas Ps3 Lan Option :
Vegas PS3 Lan Option - YouTube
4. Now go back to XLink Kai and check the Diagnostics Mode . (Clicking that globe should take you to the screen shown below. Let it sit at that screen for a few seconds, then click on the magnifying glass next to the globe in the upper right-hand corner labeled “Switch to Diagnostics Mode.”)
You must login or register to view this content.
5. In the section with the check mark, under “Network Reachable” it should read as YES. In the section with the green arrow, under “Network Card” it should read your PC's network card. Underneath that where it says “Locked” it should read as YES. If your network card is not locked, Kai will not be able to configure your Playstation 3 correctly.
You must login or register to view this content.
6. Now finally the moment of truth. Are your PS3 and Kai Engine configured correctly to work together…? Click on the folder tab underneath the question mark in the upper right-hand corner labeled “Switch to Diagnostics View.” There you should see a message that says “Sony PlayStation 3, configured successfully.” Similar to what's seen below in the picture… Yes , it's a picture of a PS2 , but if it says : configured successfully , then you're ok to go. It's also possible that you only see a mac address. If it's not red you're also ok to go.
You must login or register to view this content.
7. This is the configuration I had to do to make XLink Kai work for me. Those of whom I've helped with their setups using this same configuration have pretty much all been successful, if they've followed the directions. There are also other methods of connecting your computer & Playstation 3 to the Kai engine, such as the Dual NIC method, which can be found in the XLink Setup Help section.
8. Once you have finished playing on XLink Kai & you want to play on the PSN Network again , close XLink Kai & restart your Playstation 3 . There will be no DNS Error & you will be able again to play on PSN .
The following 3 users say thank you to Bluffed for this useful post:
09-10-2010, 03:13 PM
#2
Mirciulikkk
Climbing up the ladder
The following 3 users say thank you to Mirciulikkk for this useful post:
09-10-2010, 03:21 PM
#3
Bluffed
Wasnp
Originally posted by Mirciulikkk
Thanks for posting the ****ing obvious bro, I gave credits to the guy that made it. Go run back in your hole please.
The following 8 users say thank you to Bluffed for this useful post:
09-10-2010, 03:45 PM
#4
iVF™ Elemental
Little One
09-10-2010, 04:32 PM
#5
Mirciulikkk
Climbing up the ladder
The following user thanked Mirciulikkk for this useful post:
09-10-2010, 05:05 PM
#7
St3ven
Can’t trickshot me!
Originally posted by Bluffed
I did not make this tutorial just doing this because some people are having troubles setting it up for ps3, credits go to M1k3_NL
Ok , so you want to play Playstation 3 on XLink Kai ? No problem , just read and apply the following steps carefully.
1. Start up XLink Kai first before you switch on your Playstation 3 .
2. Switch on your Playstation 3 & you should see a message that says : DNS Error . Don't panic, it is supposed to do that . Here is a movie showing what will happen :
PS3 DNS Error - YouTube
3. Now start up a Playstation 3 game with a lan option . Go to the multiplayer part of the game and go to the lan option . Press Join Game .
Here is a movie showing the Rainbow Six Vegas Ps3 Lan Option :
Vegas PS3 Lan Option - YouTube
4. Now go back to XLink Kai and check the Diagnostics Mode . (Clicking that globe should take you to the screen shown below. Let it sit at that screen for a few seconds, then click on the magnifying glass next to the globe in the upper right-hand corner labeled “Switch to Diagnostics Mode.”)
You must login or register to view this content.
5. In the section with the check mark, under “Network Reachable” it should read as YES. In the section with the green arrow, under “Network Card” it should read your PC's network card. Underneath that where it says “Locked” it should read as YES. If your network card is not locked, Kai will not be able to configure your Playstation 3 correctly.
You must login or register to view this content.
6. Now finally the moment of truth. Are your PS3 and Kai Engine configured correctly to work together…? Click on the folder tab underneath the question mark in the upper right-hand corner labeled “Switch to Diagnostics View.” There you should see a message that says “Sony PlayStation 3, configured successfully.” Similar to what's seen below in the picture… Yes , it's a picture of a PS2 , but if it says : configured successfully , then you're ok to go. It's also possible that you only see a mac address. If it's not red you're also ok to go.
You must login or register to view this content.
7. This is the configuration I had to do to make XLink Kai work for me. Those of whom I've helped with their setups using this same configuration have pretty much all been successful, if they've followed the directions. There are also other methods of connecting your computer & Playstation 3 to the Kai engine, such as the Dual NIC method, which can be found in the XLink Setup Help section.
8. Once you have finished playing on XLink Kai & you want to play on the PSN Network again , close XLink Kai & restart your Playstation 3 . There will be no DNS Error & you will be able again to play on PSN .
Ok , so you want to play Playstation 3 on XLink Kai ? No problem , just read and apply the following steps carefully.
1. Start up XLink Kai first before you switch on your Playstation 3 .
2. Switch on your Playstation 3 & you should see a message that says : DNS Error . Don't panic, it is supposed to do that . Here is a movie showing what will happen :
PS3 DNS Error - YouTube
3. Now start up a Playstation 3 game with a lan option . Go to the multiplayer part of the game and go to the lan option . Press Join Game .
Here is a movie showing the Rainbow Six Vegas Ps3 Lan Option :
Vegas PS3 Lan Option - YouTube
4. Now go back to XLink Kai and check the Diagnostics Mode . (Clicking that globe should take you to the screen shown below. Let it sit at that screen for a few seconds, then click on the magnifying glass next to the globe in the upper right-hand corner labeled “Switch to Diagnostics Mode.”)
You must login or register to view this content.
5. In the section with the check mark, under “Network Reachable” it should read as YES. In the section with the green arrow, under “Network Card” it should read your PC's network card. Underneath that where it says “Locked” it should read as YES. If your network card is not locked, Kai will not be able to configure your Playstation 3 correctly.
You must login or register to view this content.
6. Now finally the moment of truth. Are your PS3 and Kai Engine configured correctly to work together…? Click on the folder tab underneath the question mark in the upper right-hand corner labeled “Switch to Diagnostics View.” There you should see a message that says “Sony PlayStation 3, configured successfully.” Similar to what's seen below in the picture… Yes , it's a picture of a PS2 , but if it says : configured successfully , then you're ok to go. It's also possible that you only see a mac address. If it's not red you're also ok to go.
You must login or register to view this content.
7. This is the configuration I had to do to make XLink Kai work for me. Those of whom I've helped with their setups using this same configuration have pretty much all been successful, if they've followed the directions. There are also other methods of connecting your computer & Playstation 3 to the Kai engine, such as the Dual NIC method, which can be found in the XLink Setup Help section.
8. Once you have finished playing on XLink Kai & you want to play on the PSN Network again , close XLink Kai & restart your Playstation 3 . There will be no DNS Error & you will be able again to play on PSN .
Is there any fkn things i gotta change with my ip or anything? or a port? nothing like that just download start up ps3 and follow this?
09-10-2010, 05:33 PM
#10
bensrevenge
You talkin to me?
Copyright © 2026, NextGenUpdate.
All Rights Reserved.
