(adsbygoogle = window.adsbygoogle || []).push({}); Ok I decided to make a Tut explaining how to grow good ole' CANNABIS! Indoor & Outdoor!
Credit goes to rollitup.org!
1. Things to Know About Lighting...

Color rating- Measured in Kelvin (K). The higher the number, the more bluish the light. 4000K-7000K is mostly on the blue side of the spectrum, while 3000K and under goes from a white spectrum, to a redder spectrum.

How much light is needed?
The minimum amount of light required by marijuana plants is around 3000 lumens per square foot. However, it's not 100% accurate, since although you may have a 10,000 lumen light, the amount of light that reaches the plant varies with the distance between the light and plants, and reflectivity of the grow box. The ideal amount is somewhere around 7000-10,000 lumens/sqft, and as long as the plants do not burn, as much light can be used as you want.
(*note, the sun produces about 10,000 lumens/sqft, on a sunny summer day).

Determining lumens for your grow area:
Determine the square footage of your area (example in a 4 foot by 4 foot area, there is 16 square feet)
If you have a 1000 watt High Pressure Sodium, that produces (approx.) 107,000 lumens.
Divide this by 16 (your square footage) 107,000 / 16 = 6687 lumens per square foot.
So just divide the total amount of Lumens, by the total amount of Sq ft, and thats your lumens per square foot.

How far away from my plants do the lights go?
The lights in your grow room should be as close as possible to the plants without burning them. There is no such thing as too much, unless there is sufficient heat to dry out and burn the leaves. A good rule is to put your hand under the light, if its too hot for your hand, chances are that the plants will be too, so move the light up until your hand feels more comfortable. For seedlings and clones, I keep them a little further away from the light, because they are very susceptible to burning and drying out, at these stages.

Efficiency is very important when choosing a type of light. The wattage is not the most important thing, as you can see below, different types of light produce different amounts of lumens per watt. A 300 watt incandescent will produce about 5100 lumens. While a 300 watt Metal Halide (just an example, they do not come in 300 watts), will produce 27,000 lumens. Obviously far more efficient for growing, while still using the same amount of electricity.

Approximate light production:
Incandescents: 17 lumens/watt
Mercury vapor: 45-50 lumens/watt
Fluorescents: 60-70 lumens/watt
Metal halide: 90 lumens/watt
High pressure sodium: 107 lumens/watt

Incandescent lights: Incandescents are the most popular type of lights in the world. They may come advertised as incandescent, tungsten, quartz, halogen, or simply standard. The important thing about incandescents is this: they suck.
There are some incandescents which are sold as 'grow lights.' They usually have a blue coating and usually come in 60W and 120W sizes. While they may seem like a good choice to new growers, they are next to useless; they produce some light at a usable spectrum, but only have about a 5% efficiency and generate more heat than usable light. Most of us have these in our homes right now. Don't use them for growing, instead opt for a Compact Fluorescent as a cheaper but more efficient alternative.

Fluorescent lights: Fluorescents are a lot more useful than incandescents. Their efficient enough, and cheaper than HID lights. Compact fluorescent tubes are popular with growers because of their good output to size ratio. Compared to standard 4' tubes, compact fluorescent bulbs are smaller, and more can fit into a given area. Fluorescents are good for small grows on a tight budget, and for novice growers, since they do not require any special sort of wiring or understanding of the necessary bulbs for a given fixture, and are very widely available.
Fluorescent lights come in many different Kelvin ratings; often the spectrums are labeled on packaging as being 'cool white' or 'warm white.' Cool white is more blue, and is good for the vegetative stages of growth, and warm white light is more orange or reddish, and is best for the flowering stage.

High Intensity Discharge (HID) Lighting Systems:

Mercury Vapor (MV)
Mercury vapor lights are not the most efficient light for growing. They are very bright, and relatively cheap. They do emit light at the wavelengths necessary to support your plants growth, but not nearly as good as a MH or Hps light. Much of the light emitted by MV lights is bluish-white. Street lighting is what most MV lighting is used for.

Metal Halide (MH)
Metal halide lighting systems are optimal for use in the vegetative phase of growing. They emit mostly blue light, which encourages vigorous growth of foliage. They are very efficient, but can get rather expensive to start with; fluorescents may seem more appealing because of their lower price, and they are not much different when compared on a lumen-to-lumen cost level. These lights can be used through-out the grow, but will most likely result in light, fluffy buds.

High Pressure Sodium (HPS)
High pressure sodium lights emit mostly orange, yellow, and red spectrum light, which is perfect for the flowering stage of the plants growth. They are (in my opinion) the most efficient type of light available for any application. HPS lights can be used through-out the entire grow. They produce more dense and usually larger buds than any other light.
HPS lights are generally a little more expensive than MH systems of similar wattage. They are more commonly used by experienced growers because of their ability to produce tighter buds, higher lumen-output-per-watt, and will produce from start to finish.

2. Water: The most essential compound

Water is water right? Wrong. I see a lot of growers that have all this knowledge about nutrients and photoperiods but know very little about the water they use and that not all water is created equal and some water isn't very well suited for growing at all. I decided to do this thread to help educate growers about the water they use and why it's important to understand "The most essential compound".


What is "Hard Water"?

Perhaps you have on occassion noticed mineral deposits on your cooking dishes, or rings of insoluble soap scum in your bathtub. These are not signs of poor housekeeping, but are rather signs of hard water from the municipal water supply. Hard water is water that contains cations with a charge of +2, especially Ca2+ and Mg2+. These ions do not pose any health threat, but they can engage in reactions that leave insoluble mineral deposits. These deposits can make hard water unsuitable for many uses, and so a variety of means have been developed to "soften" hard water; i.e.,remove the calcium and magnesium ions.
Problems with Hard Water

Mineral deposits are formed by ionic reactions resulting in the formation of an insoluble precipitate. For example, when hard water is heated, Ca2+ ions react with bicarbonate (HCO3-) ions to form insoluble calcium carbonate (CaCO3), as shown in Equation 1.


(1)


This precipitate, known as scale, coats the vessels in which the water is heated, producing the mineral deposits on your cooking dishes. In small quantities, these deposits are not harmful, but they may be frustrating to try to clean. As these deposits build up, however, they reduce the efficiency of heat transfer, so food may not cook as evenly or quickly in pans with large scale deposits. More serious is the situation in which industrial-sized water boilers become coated with scale: the cost in heat-transfer efficiency can have a dramatic effect on your power bill! Furthermore, scale can accumulate on the inside of appliances, such as dishwashers, and pipes. As scale builds up, water flow is impeded, and hence appliance parts and pipes must be replaced more often than if Ca2+ and Mg2+ ions were not present in the water.
Some Strategies to "Soften" Hard Water

For large-scale municipal operations, a process known as the "lime-soda process" is used to remove Ca2+ and Mg2+ from the water supply. Ion-exchange reactions, similar to those you performed in this experiment, which result in the formation of an insoluble precipitate, are the basis of this process. The water is treated with a combination of slaked lime, Ca(OH)2, and soda ash, Na2CO3. Calcium precipitates as CaCO3, and magnesium precipitates as Mg(OH)2. These solids can be collected, thus removing the scale-forming cations from the water supply.
To see this process in more detail, let us consider the reaction for the precipitation of Mg(OH)2. Consultation of the solubility guidelines in the experiment reveals that the Ca(OH)2 of slaked lime is moderately soluble in water. Hence, it can dissociate in water to give one Ca2+ ion and two OH- ions for each unit of Ca(OH)2 that dissolves. The OH- ions react with Mg2+ ions in the water to form the insoluble precipitate. The Ca2+ ions are unaffected by this reaction, and so we do not include them in the net ionic reaction (Equation 2). They are removed by the separate reaction with CO32- ions from the soda ash.


(2)


Household water softeners typically use a different process, known as ion exchange. Ion-exchange devices consist of a bed of plastic (polymer) beads covalently bound to anion groups, such as -COO-. The negative charge of these anions is balanced by Na+ cations attached to them. When water containing Ca2+ and Mg2+ is passed through the ion exchanger, the Ca2+ and Mg2+ ions are more attracted to the anion groups than the Na+ ions. Hence, they replace the Na+ ions on the beads, and so the Na+ ions (which do not form scale) go into the water in their place.

[ame]https://www.youtube.com/watch?v=QarYCDrrQt4[/ame]

If you have any questions I will be glad to help you! I can post more tips on how to grow but just to much to write so if you want me to keep posting just keep this thread alive!

You've never smoked it then......

Ngu should have a weed shop, or you should be able to donate weed to become premium

Lol at the young children in this thread.

LMAO at ozzy and shockk they think Marijuana hurts u. If so then why do Doctors Prescribe it to people? and why is there so many Marijuana Shops out there for? theres over 200 shops here in Los Angeles

You must login or register to view this content.

You must login or register to view this content.

i didnt read it all but i didnt see you explaning how the male plant helps the female and eventualy kills is if u leave in unatended

fagget addicts who NEED weed said no thanks and guys GROAN ME WEED IS GARBAGE I don't give a flying ****

sorry longjonsilver delete this post if you want I didn't notice your post

totally copy and pasted huh?
Pro-Tip:post the source my dude
anyways, haha this is pretty true, but it costs a lot to start growing big, but a plant or two is definitely simple and don't need such a big setup :black: