(adsbygoogle = window.adsbygoogle || []).push({}); Based on the TUT made by Vectrixx. Read it to learn how to find the values.


Edit
To Make things easier I will add the simple method of weight modification to the OP.

Credit to mexplayer83 for pointing it out.

[ATTACH=CONFIG]23243[/ATTACH] You must login or register to view this content.

The 64 is equal to 100% of the current weight of the car. So using 00 - 63 will give you a weight reduction.
If you use 65 - FF you will get a weight addition to the car. So a 1000kg car at FF will weigh 2550kg. The same 1000kg car at 0A will weigh 100kg.

--------------------------------------------------------------------------------------


This is the way I have found to decrease the weight of the car.
Note: It may take some trial and error to find the exact weight that you want in the end.

Be sure to add all 3 codes for the Weight Reduction Stage 1. Then use the multiplier to reduce weight.
Edit: I have noticed that you don't have to change the final code in 0000E9A0. Just the first 2 codes will reduce weight.

And Just like any other modification you must do a car wash, oil change, start a practice lap, ect. Once you exit and the game saves the changes made will be visible in the garage.

[ATTACH=CONFIG]22650[/ATTACH] You must login or register to view this content.

0000E820 : 00 03 FF FF FF 00 01 00 00 42 41 09 48 00 01 00
Makes the part "Weight Reduction Stage 1" purchased in game.

0000E820 : 00 03 FF FF FF 00 01 00 00 42 41 19 48 00 01 00
Makes the part "Weight Reduction Stage 2" purchased in game.

0000E820 : 00 03 FF FF FF 00 01 00 00 42 41 39 48 00 01 00
Makes the part "Weight Reduction Stage 3" purchased in game.

0000E8B0 : 11 E5 00 00 13 59 00 00 00 0A 00 00 09 34 00 00
Is the car part installed on you car. This is where you use the multiplier of your choice to reduce weight.

Edit: Now I've noticed something. The multiplier only seems to work within a range of weight. About 150kg from wherever the Weight Reduction stage puts you to start. An example being the Lambo Murcielago. It starts at 1665kg. Stage 3 Weight reduction puts it at 1365kg. I was able to reduce that down to 1232kg. But then the number would either begin to increase again or just drop all the way to 0kg. So it seems this method has huge limitations, but is good for getting a car to 0kg.

Weight multipler?!

My RE雨宮FD only have FF FF in these value by default, of coz not 0kg

is there any limit for using these code e.g. special car ,racecar cannot perform weight multipler?

Be sure to add all 3 codes for the Weight Lvl 1 Reduction.
As in the 09 in line 0000E820.
The 00 00 09 34 from 0000E8B0.
And the 12 50 from line 0000E9A0.

Then you can modify the multiplier to whatever you want. Just did it on a Nissan R92CP Race Car '92. No weight reduction available in the tuning shop. Added the codes in HxD used the FF FF multiplier and it was 0kg in game.

i tried to add in my FD
but nothing change in game...

when i decrypted the save file again, modified code has returned to 000000 etc..


i will try again later thx

THX bro~
I done, Tokyo Extreme Racer ZERO spec. White Charisma RX-7
1106ps, 998kg

what shall i put in to add weight?

Do both multiplier bits need to be changed?

If u set the car to 0kg is it suppose to bounce around? Or I did something wrong? I set my subie with a 3 stage weight reduce then change the value u said and I had -15kg but I added 200kg on the ballast now its jumping like crazy..oh and can I get the hex value for 150kg?

I'm also interested in this, is it possible? Tried a few combinations but no luck. Weight reduction works (shows up as installed) but weight doesn't change at all no matter what i put.

Edit: The solution was in the "Hybrid Builder for Spec 1"-thread

Pretty sure you don't need to add the weight reduction codes at all, just altering the offsets E8BC-D is enough to remove weight, at least its always worked for me, a bit like the fact that you don't need to add customisable suspension in order to lower ride height