(adsbygoogle = window.adsbygoogle || []).push({}); PICGroove Mod PS3 SixAxis Guide

This Mod is based on a pic 18F2550 PsgrooPic with Sixaxis PS3 controller adapted to take into account that will comply with 2 main functions:

Ps3 launch debug mode without losing any original settings and also be updatable.

Clarified, as any MOD is to make use of solder on the board of control, nothing complicated, only 8 of them.

Materials:

* 1 Control Sixaxis PS3 (in my case I have one of a pack of 80g without vibration, worth also for the Dualshock 3 but I have not tested).
* 1 Pic 18F2550 and have a list to create a Picgroove both components as the programmer. In EOL there are many tutorials about it, I personally used the scheme th0rin in version 1.2, ie PSGroo 1.2.pdf. Also do you can see from this link: You must login or register to view this content. a quote from our friend calvo225, follow all the steps until you have the pic set. I recommend the program developer Art2003 WinPic800

NOTE: The pin 26 has to go to ground if you selected the option LVP tab WinPIC800 Config. If not used the LVP option, not necessary.

* Cable to make posts (use data cable for hard disk ide 80-wire very pratico and a single hair).
* Soldering iron, tin, scissors, paste flux, etc.

Construction: We take the pic and the file previously scheduled PSGrooPIC_wBTL_HEX_V1.5.hex all legs will bend to fit it neatly into a place of control:


This is the place you got the pic goes perfect, put the legs, facing away"




And seeing where it goes our pic we took, we cut pieces of ide cable no more than 5 cm. And proceed to solder the points: 1,8,9,10,13,14,15,16,19,20,25,26 one for each point. Remember that the pic is looking out the points 15,16,19,20, 25 and 26 are below the pic and would have to fold them up, nothing complicated for the other points is easier as they are in the superior.

Now we have to weld all the components necessary for the Pic:

* 2 resistance of 10 k.
* 1 330 ohm resistor.
* 1 Capacitor of 220 or 470 nf.
* 2 22 pf capacitors.
* 1 Crystal 8, 12, or 20 mhz.
* 1 Capacitor 100 nF.
* 1 LED (any color, I have not installed).

POSE follow this outline for easy interpretation:

Oversided Picture: You must login or register to view this content.

Using pieces of ide cable to connect a pic, the theme of Jumper and DC outputs, D +, D-and NRM leave enough cable about 10 cm or so to be comfortable installation whether to cut it short. The LED do not place out and I do not think it takes, now if someone wants to put it, in this photo show more or less as it should be before welding something I also can find another way to put to me was the best I found:


CLARIFICATION:

Before welding something in command must prove that pic works correctly I connect to the outputs VCC, D +, D-and NRM a USB connector and see if I tore the exploit, if all goes well we proceed to the step of welding at the helm, the points are marked with colors that are welded to the plate as is without changing anything.

Oversized Picture: You must login or register to view this content.

See diagram that goes as everything goes online are simple welds, in the part of JUMPER must draw the two lines and put in the right stick button (THIS IS TO UPDATE THE PIC FOR FUTURE UPDATES PSGROOVE).

In the top right Note that there is an extension of the RESET button I have long, I've added a switch and that is adapted to the control unit had to use a Dremel to fit it and leave it outside (this is the most important of all that the action cancels any usb functionality sends ushering in the Exploit). Authorities recommend any place to plug insulators between the wires, the pic and mini usb connector to ensure proper operation.

Operation:

* To start the Xploit just put the usb cable to the console and controller, having previously turned off and the console on the back button after having pressed the RESET button and then press the POWER button then the button to activate Ejeta DEBUG , wait until you leave the logo of the console, you can remove the knob and press the PS button (the middle of the panel with the initials PS, look for games and you'll see two folders that indicate that everything went well.
* To update the PIC must have these programs installed on your PC:

1. vcredist_x86.exe (You must login or register to view this content.)
2. dotNetFx40_Full_setup.exe (You must login or register to view this content.)

After installing run the program:

3. HIDbootloader.exe which is responsible for programming the pic, put the usb cable on the remote simultaneously have tightened RESET button and left stick button (reset button is to disable any USB activity in the control and the left analog stick makes its way to activate the bootloader mode of the pic) and have fulfilled that is enough to install the other end of the usb cable to pc.

The program will automatically detect the device. The same is done at the beginning of the Institute prior to installation on the remote to program. Hex of the exploit, the program's interface is very easy to interpret.

Note: do this only when we have a new update for Pic, we must take into account that you have installed the latest updates and we can play without a disc inside (in some cases there are games that deserve it.)

Well so far all for now, I hope for something to serve this project for me has been very encouraging to have done it despite the bad reviews I've had thanks to all who supported me and the team of Eol.

Greetings

Attached Images
File Type: jpg 25742935.jpg (58.1 KB, 1685 views)
File Type: jpg p100921214927.jpg (693.7 KB, 83 views)
File Type: jpg p100921214950.jpg (751.5 KB, 90 views)
File Type: jpg 63785771.jpg (68.7 KB, 1614 views)
File Type: jpg 75121596.jpg (67.0 KB, 1594 views)
File Type: jpg 21889808.jpg (102.9 KB, 179 views)
File Type: jpg 15325199.jpg (73.1 KB, 1596 views)
File Type: jpg 68571918.jpg (96.2 KB, 194 views)
Attached Files
File Type: zip PSGrooPICV1.5_HEX_wBTL_CCS.zip (11.3 KB, 34 views)
File Type: pdf PsGroo 12.pdf (29.0 KB, 78 views)


Read more: You must login or register to view this content.

damn, I was hoping I could just plug the controller into the computer, load some crap onto it and be done.

Lol me too, I'll not do that, I'll just wait until my PS3 arrive and JB it

me to ha doesn't the world

This is a whole new mod

how gay man they made it sound like it would be easy ,untill the guide came out u have to buy conponents etc. it just as gay as making a 360 nand reader ,which is prob what ill do as dont know which sites can be trusted to buy off and the ones i can trust have no boards in stock cant get anything here in UK

i thought it would be a program to a pc and then you plug it in via usb and VOILA your ps3 sixaxes is programmed to jailbreak.

So can we jailbreak 3.50 with this?

NO!!!!!!!!!!!!!!!!!!!!!!!

or i can buy a usb dongle