Post: ProgSkeet: Solderless Video Released And More Updates
Options
08-03-2011, 08:47 PM
#1
-Daemon-
HELL IS HERE
here a video of the progskeet for you guys hope you enjoy not my video
Originally posted by another user
Originally Posted by uf6667
I would like to add one thing, in case you haven't noticed: it's not about the speed, that train's long gone.
no, this time around we have the SOLDERLESS CLIP attached to the NAND.
sure, it has wires soldered to it but this is just because there is flex pcb yet to connect to progskeet
once it's all tested and flex pcb is designed, this will be 100% solderless
I would like to add one thing, in case you haven't noticed: it's not about the speed, that train's long gone.
no, this time around we have the SOLDERLESS CLIP attached to the NAND.
sure, it has wires soldered to it but this is just because there is flex pcb yet to connect to progskeet
once it's all tested and flex pcb is designed, this will be 100% solderless
Originally posted by another user
He also tweeted the wrong diagram was released for the Dual-NAND setup, so we attached the right one below with the new updated software!
DIAGRAM Changes:
03/08/2011
- Removed DualNandNew.bmp (this is for prototype, sorry)
- Added Dual NAND diagram (with the switch), read below for instructions.
02/08/2011
- Added new NAND/Dual NAND diagram. Power up the console with the switch set to "off". When the console is on, you can switch it to "on".
FLASHER Changes:
110802
- Added more selections to Block Count (bigger NANDs)
110803
- Fixed: issue with "Test Shorts" - ONLY USE THIS WHEN PROGSKEET IS NOT CONNECTED TO ANY DEVICE!!! OTHERWISE IT GIVES FALSE POSITIVE!!!
yours truly,
uf6667
DIAGRAM Changes:
03/08/2011
- Removed DualNandNew.bmp (this is for prototype, sorry)
- Added Dual NAND diagram (with the switch), read below for instructions.
02/08/2011
- Added new NAND/Dual NAND diagram. Power up the console with the switch set to "off". When the console is on, you can switch it to "on".
FLASHER Changes:
110802
- Added more selections to Block Count (bigger NANDs)
110803
- Fixed: issue with "Test Shorts" - ONLY USE THIS WHEN PROGSKEET IS NOT CONNECTED TO ANY DEVICE!!! OTHERWISE IT GIVES FALSE POSITIVE!!!
yours truly,
uf6667
As always for more information, support, and latest updates visit their official site: You must login or register to view this content.
SOURCE AND DOWNLOAD
You must login or register to view this content.
The following 3 users say thank you to SavageCHRIS for this useful post:
The following user groaned SavageCHRIS for this awful post:
08-03-2011, 09:05 PM
#3
TechMemphis
< ^ > < ^ >
Could prove to be quite awsome if a solderless clip is sent to the market place... I would love one. Although I do enjoy the challenge of a good solder and had planned on ordering a teensy board tomorrow after I get paid tomorrow... oh well may wait to see how this goes instead beats messing with soldering on my ps3 and risking turning it into a paperweight...
08-03-2011, 11:00 PM
#4
MCPADDINGTON
Banned
08-03-2011, 11:47 PM
#5
PS3 Prodigy
(ಥ_ಥ
08-04-2011, 12:42 AM
#6
DemonPaladin
Bad Meets Evil
08-04-2011, 02:12 AM
#7
PS3 Prodigy
(ಥ_ಥ
Originally posted by DemonPaladin
Hey umm do you know when dual booting off the nand will be possible? Or if it already is.
Yes dual Nands is possible and their was a thread about someone that is working on it but it's still in the testing phase and they haven't released the method yet. it was originally posted on You must login or register to view this content.(Spanish site) then was posted on You must login or register to view this content.
The following user thanked PS3 Prodigy for this useful post:
Copyright © 2026, NextGenUpdate.
All Rights Reserved.
