(adsbygoogle = window.adsbygoogle || []).push({}); I have seen this asked so many times and the answer is always the same "search on youtube or google it" well i thought i would just search this as i had a bit of spare time and wanted to help. This has probably been done before but when i search i only get a how do i? and a pdf file. this was found on another site.

You will need:

1.) Heat gun (temperature controlled preferably).
2.) Isopropyl alcohol (acquire from chemist).
3.) Vacuum cleaner or compressed air blower.
4.) Phillips screw driver.
5.) Flat blade screw driver or slotted torx bit.

Instructions

1. Remove warranty sticker and rubber foot thats positioned above hard drive bay.
This will invalidate any warranty.

2. Using a small flat blade screw driver or slotted torx bit, unscrew cover plate screw.

3. Slide cover plate towards the left until it stops and lift off.

4. Remove all Phillips screws marked noting size and position.

5. Hinge case towards you until disengaged and then tilt towards the left. See below.

6. Remove ribbon cable by carefully lifting black part of connector (locking tab).

7. Lift/tilt blue ray drive towards the right whilst disconnecting power cable and the large ribbon (lift tab) underneath.

8. Remove 5 screws and the earth wire screw on psu, and unplug connector plug.

Before removal of psu unplug small bnc connector (black wire) and remove tape on side of psu, now lift off psu.

9. Now remove the wide ribbon from connector (lift tab) unscrew the four screws on the Bluetooth board and remove.

10. Remove hard drive cover.

11. Unscrew blue hard drive screw and disengage hard drive by sliding towards gap in the bay.

12. Remove hard drive, see below.

13. Unscrew 4 screws holding the bracket, on/off and eject control panel. Remove small ribbon (lift tab) and remove control panel.

14. Unscrew 8 screws.

15. Lift enclosure out of plastic base, see below.

16. Now unclip black rear panel and remove.

17. Unscrew 4 screws and remove sprung brackets, see below.

18. Lift of metal cover plate whilst allowing ribbons to pass through gaps in plate without damage, see below. (Taking note where heat sink rubbers are positioned).

19. Supporting fan assembly turn board over, remove fan power connector and fan.

20. Remove 2 screws holding plate to hard drive connector and unplug battery connector.
Now remove plate.

21. Clean off old heat sink compound from the 2 mainprocessors using Isopropyl alcohol making sure all traces of the old heat sink compound has gone.

22. Clean both touch plates on bottom of fan/heat sink assembly with Isopropyl alcohol until all traces of the old heat sink compound has gone.

23. Now using a vacuum cleaner or compressed air blower get rid of all dust build up in the case and on all component parts of the ps3 (pay special attention to the fan assembly and heat sink fins(MUST BE CLEAR OF DUST).

24. Typical example of dust build up.

Ps3 case (dusty).
Heat sink plates before
heat sink compound removed (dusty).

25. Once cleaned you should now have a nice pile of bits that looks something like this, see below.
Now for the tricky bit!

26. Check the top metal cover plate (underside) for burn-in marks, as you can see below this ps3 got very hot before it yloded!

27. Place the ps3 mother board on a flat heat resistive surface (kitchen work top or melamine shelf will be fine).

28. Turn heat gun on and set temperature to 350 deg and the fan speed to low (to high and it will move the surface mount bits).Allow gun to get up to temperature before continuing!

29. Using a circular motion hold heat gun over areas outlined below (keep heat gun an inch above
board/components at all times).

30. CPU side first.

31. After 15 to 20 seconds move onto the next area.

32. Once all marked areas have been heated/reflowed on the mother board LEAVE for at least 10 to 15 minutes to cool. (DO NOT MOVE MOTHER BOARD WHILE COOLING).

33. A popping noise may be heard during cooling, dont worry this is normal.

34. NON CPU side.

35. After 10 to 15 seconds move onto the next area.

36. Once all marked areas have been heated/reflowed on the mother board LEAVE for at least 10 to 15 minutes to cool. (DO NOT MOVE MOTHER BOARD WHILE COOLING).

37. A popping noise may be heard during cooling dont worry this is normal. Heat sink compound still on in this picture, remove before reflowing. Heat sink rubber pads still on in this picture remove
before reflowing also hold ribbons out of way while reflowing

Congratulations!!

You have just repaired youre yloded ps3 mother board.

38. Now its time to apply new heat sink compound to the 2 processors, when doing this its always best to follow the manufacturers instructions but I believe the process is the same with all types (please check instructions that come with paste), before continuing

39. The paste I am using is called AKASA 450 its a silver based compound with a thermal conductivity of 9.24w/m deg c and an operating range of 0 to 200 deg c. You can buy it from most pc shops but I get mine from my local Maplin ( I have been told that there is a better compound on the market called arctic silver but I havent tried it as yet so the choice is yours).

40. Use syringe supplied and dispense a small worm of compound from top to bottom on the left hand side of processor chip, now using credit card supplied spread compound evenly and thinly over processor face (to much is bad and not enough is also bad) the ideal amount is when you can almost see through the paste.

41. Now repeat on the other processor.

42. See below.
NOW IT IS TIME TO REASEMBLE THE PS3.
RETRACE YOUR STEP IN REVERSE TO REBUILD
MAKING SURE ALL RIBBON CABLES HAVE BEEN
FULLY INSTERTED INTO CONNECTORS AND LOCKED
DOWN IE. (TABS).

[ame=https://www.youtube.com/watch?v=U70SgRDVcBo&feature=player_embedded]YouTube - ps3 ylod fix part1 gilksy[/ame]
(part 1) found on youtube no credit to me plz credit guy who posted.

[ame=https://www.youtube.com/watch?v=TePnCFKionE&feature=player_embedded]YouTube - ps3 ylod fix part2 gilksy[/ame]
(part 2)

[ame=https://www.youtube.com/watch?v=eCYZ5ksExsk&feature=mfu_in_order&list=UL]YouTube - ps3 ylod fix part3 gilksy[/ame]
(part 3)

[ame=https://www.youtube.com/watch?v=pGIE77M8zu4&feature=player_embedded]YouTube - ps3 ylod fix part4 gilksy[/ame]
(part 4)

[ame=https://www.youtube.com/watch?vINm3jbZPRE&feature=player_embedded]YouTube - ps3 ylod fix part5 gilksy[/ame]
Part 5

[ame=https://www.youtube.com/watch?v=c6ooJqJgk9E&feature=player_embedded]YouTube - ps3 ylod fix part6 gilksy[/ame]
(part 6)

Hope this helps??

Copy & Paste :carling:

You are correct and i apologise for any confusion i may have made that cast doubt so i have reworded my original statement to add that this was found elsewhere but i had already said that the vids were not mine so plz give credit to that guy. Sorry for any confusion i caused. I was trying to help.

It only lasts for about 2 weeks then dies again anyway.

nope mine lasted 2 months doing this :p

really? mine only lasted 2-3 week

:p maybe you did somthing wrong haha i dont play much either do you play alot :\

Cool tutorial
Should personalize it more :y:

if only i had a heat gun..

I didnt want to personalize as when i did i got the copy and paste message (which a lot was) so i de-personalised it and went simple but now have found that there is one with same vids in exploits and hacks but when i searched for it it never came up on search? And why on exploit page?

---------- Post added at 04:30 PM ---------- Previous post was at 04:29 PM ----------



They are not expensive probably £12 from argos